博科光纤沟通机zone差异指令办法
Brocade（博科）沟通机为例，记载其差异指令和差异办法：

联接沟通机：可经过串口或网线从IE进入，默许IP　　10.77.77.77 , 255.255.255.0

创立ZONE有两种办法：
一是经过沟通机port号，二是经过主机和存储的WWN号　（单个硬盘没有WWN号，存储全体才有一个）

指令：
查看其时zone情况：zoneshow
删去zone : zonedelete "zone_name"
查看domainID 和沟通机称号：　siwtchshow
按上图创立zone:
创立zone : zonecreate "zone_name1","1,0;1,1"
zonecreate "zone_name2","1,9;1,8"
zonecreate "zone_name3","2,0;2,1"
zonecreate "zone_name4","2,8;2,9"
创立zone后经过进一步创立cfg来安闲组合或分拆等来处理ZONE
cfgcreate "cfg_name","zone_name1;zone_name2"
cfgenable "cfg_name"
cfgsave
cfgdelete "cfg_name"
cfgadd "cfg_name","zone_name"或"zone_name3;zone_name4"
cfgremove "cfg_name","zone_name" （并非删去ZONE，仅仅将其移出这个CFG）

经过WWN创立ZONE：
查看光纤卡的WWN号：
lsdev -Cc adapter|more fsc
lscfg -vl fsc(0-9)　就能看到WWN号
创立正本和PORT号相同：zonecreate "zone_name","234234234234234;423424234234234"

另附MCDATA沟通机的装备：

mcdata沟通机笔记

1.显现其时zone信息：show zoning：

Root> show zoning
当然也能够用show all来查看悉数的信息
查看其时信息（习气行的，可不做，仅仅为啦保存下其时的装备信息）
Root> config zoning showActive
2.增加zone
2.1首要Root> config zoning replaceZoneSet
当然上面这不也能够不做要素如下：
There are 2 ‘configure areas’ in the switch, the ‘Active’ and the ‘Pending’, you can’t

edit the Active zoneset directly, all your changes are made to the ‘Pending’ or named “Work

Area”, but this 2 ‘areas ’ are NOT always the same, so it’s better to let the pending work

area be same with the Active configuration
2.2 增加zone
Root> config zoning
Config.Zoning> addzone xx__eva_sma
2.3 将一个port成员参加到zone1中：
Config.Zoning> addPortMem zone1 1 26
该指令将domain ID为1的沟通机上的26端口划入zone1中。
将一个WWN成员参加到zone1中：
Config.Zoning> addwwnMem zone1 50:06:0b:00:00:27:11:78
或许直接Root> config zoning addWwnMem TheUltimateZone 10:00:00:00:C9:22:9B:64
从一个zone中删去一个端口
deletePortMem xx__eva_sma 11 141
deletePortMem xx__eva_sma 11 142
deletePortMem xx__eva_sma 11 140
2.4 激活zone装备：
Config.Zoning> activatezoneset
或许 Root> config zoning activateZoneSet
2.5 查看zone情况
Config.Zoning> showactive
2.6 经过此指令可查找到联接到该沟通机设备的wwn号
Root> show port status
2.7 删去zone
Root> config zoning deleteZone TheLeastUltimateZone

M-SERIES (McDATA) COMMANDS
M-SERIES Switch Commands
View= config ip show
Config ip (new IP and Subnet mask)
Show switch
Show switch
Show system
Show nameserver
Show loginServer
Show nameServer
Show.Fabric nodes
Maint system setOnlineState
M-SERIES Zoning Commands
Config.Zoning addWwnMem zoneName wwn
Config.Zoning addZone add a new zone to the working area
Config.Zoning activateZoneset activation of changes
Config.Zoning showactive shows actively connected running zoneset
Config.Zoning clearZone clear WWNs in a zone
Config.Zoning deletezone remove zone from the running config
Config.Zoning showPending show pending zones
Config.Zoning renameZoneoldzonenamenewzonename
Config.Zoning deleteWwnMem zonenamewwn
Config.Zoning renameZoneSet zoneSetName

上一篇：光接纳机活络度的界说

下一篇：远程主干网光纤选型主张